Tuesday, September 19, 2017

A Fat Trike is born!



I had finally put together (I thought) all the parts needed to finish building my trike. The first step in getting this beast rolling was front wheels, which I decided to build from scratch so I could use my favorite Sun Ringle Mulefut rims. Azub had provided the trike specific fat front hubs so I took the components to the shop for assembly. Calculating the spoke length was tricky because although there was no necessary dish (offset) to the wheels, there was also no locknut with which to measure for spoke calculations! I finally decided to use a thru axle adapter to create a point of reference and managed to get a spoke length I hoped would be correct. It turned out they were probably one millimeter too short, which doesn't seem like much, but in wheel building can be problematic. I'm sure they will be fine, but I wish they had that extra millimeter. Mounting the tires was literally a snap. The Mulefuts and Schwalbe Jumbo Jims are very easy to set up tubeless, which was one of the reasons I wanted to use that combination, and they popped right into place with no leaking whatsoever. 



A little Spoke Prep on the threads, colored so you remember right from left!



The massive amount of offset made for an unwieldy build but makes a really strong wheel, although the nipples are under tremendous stress with the bracing angle



The first wheel, laced up and ready for truing. The wheels are built offset dishless using only one set of spoke holes.



And both wheels ready to go!

The next step was assembling the frame components. The frame plates were thoroughly greased and torqued together using the excellent threaded alignment pins


Definitely more secure than a folding frame design

Then I was able to mount up my newly built front wheels.


I really need to build a trike repair stand!



Both wheels on



Here I have to point out one of my first minor criticisms of the Azub Fat Trike...the quick release skewers. They are right and left hand threaded, which I guess makes sense? But they are very awkward to use and the leverage is either too tight or too loose, it's hard to find the sweet spot. And as the axle doesn't reference or "key into" the king pin in any way, trying to get the QR in the right spot to close so it's facing back under the frame crossbar just right is an exercise in frustration. Perhaps if you carry a Torx wrench, which is an uncommon size, to align the axle just right, but who wants to carry an extra tool just to install your wheels when the whole point is that they are quick release? I was just going to swap the QR's out for stainless bolts, but one of them being reverse thread eliminates that possibility. Maybe there is a trick I don't know, but I doubt it.

The next step was to mount the brakes. I ran into another snag here because the trike uses 140 caliper mounts even though the rotors are 160, or at least that was what I was using. And, of course, I only had one 140 caliper mount. Dammit! Well, I could at least get one mounted.







Having fussed with the QR's and mounted the front wheels and right brake I came upon my first major setback. The Azub rear frame is spaced at 190mm, the same as my Carver fat bike frame...I thought. Dammit! The Carver frame is 170, not 190! The beautiful Hope Fatsno rear hub I already had was useless, meaning the entire wheel was useless. I had to order another rear hub and rebuild the rear wheel, crap. Fortunately, the distributor is fast so I had another hub in no time and built and installed the correct rear wheel.



Wrong rear wheel just sitting in the frame to see what the trike looks like



My trike build stand. Right QR is wonky as usual.


In order to install the crank, I needed to install the boom, which went together with no problems. I wish the boom had a center mark on it to make centering it easier, but there is nothing there so you just have to eyeball it or use a level. I eyeballed it.



Boom installed. The rack mounts to the seat, which makes taking it off impossible, even though it has quick releases to do so. What is it with the QR challenges on this trike?

The Race Face Next Sl crank I was using was set up for a fat bike bottom bracket width and the fat trike has a standard bottom bracket width. Fortunately, the Next Sl crank is "future proof" and has a replaceable spindle to accommodate different frame standards. Swapping it out was simple enough with a youtube tutorial, and Race Face even provides the tool necessary to do it, nice! Once the spindle was swapped, I realized one of the tools I did NOT have was the Race Face proprietary bottom bracket splined tool, so there was no way to install the bottom bracket. Sigh. A trip to the shop to borrow the correct tool and I had the BB installed and ready for the crank.


Next Sl crank with old spindle removed and new one waiting to be installed



The finest crankset on the market!

I really like having bar ends on my trikes. It gives you a very natural place to rest your hands when riding on the flats and uphills, although I don't recommend it for the downhills! I was also excited to have internal cable routing in the bars, meaning I could run my brakes and shifter the "right way up" instead of inverted like you usually have to do on a trike.


Right way up brake lever and comfy bar end



Ready for cable and housing and final adjustment

While I was waiting for an opportunity to get the trike into the shop for cable and housing I mounted up the auxiliary bag under the seat. I was so psyched they made this adapter because I had an Ortlieb handlebar bag that had been sitting around for years without my being able to use it. With the adapter, it is a perfect fit and is a great place to put those things you need ready access to while riding.


Ortlieb handlebar bag



Mounted under the seat on the wonderful Azub bar bag adapter



Almost ready for adventure!



Glamour shot

I finally had a free day to get the trike into the shop and cable it up. I started with the brakes. The front brakes are fairly simple, although the left brake caliper is mounted upside down so needs some creative cable routing. I ended up using V-brake noodles to simplify the cable run. The shift cable housing was a little bit more of a challenge because Azub only provides one cable guide on the bottom of the frame so you have to run a lot of zip-ties along the frame to keep the housing run clean and tidy. I'm not a big fan of zip-ties along the frame, I think it looks janky and I would much prefer to have integrated cable guides.



Internal routing is so nice and clean



Plenty of room for two pieces of housing

Azub provides a caliper mount for attaching a rear disc brake as a parking brake. I really like this idea so that was the way I went. I came up with another challenge here though in that I could not figure out an acceptable way to actuate the disc parking brake. I ended up buying a Paul downtube shifter adapter and mounting it low on the left bar with a Dura-Ace shifter as a brake lever. I'm not at all happy with it, and the holding power is terrible, but it is the only thing I have been able to figure out for now. I'm sure I will come up with something better at some point.


Rear disc parking brake



Paul thumbie with Dura-Ace shifter as a parking brake lever

And last but waaaaaaaaay not least I needed a chain. Well, not "a" chain, actually THREE chains! It takes a lot of chain for a recumbent, much like a tandem. But with the chain installed and some minor tweaks to the shift adjustment, the trike was ready to ride!!!



Get out of its way, this thing ain't stopping for no one!


As I have said before, I am extremely impressed with this trike. There are a couple of little nitpicky things that I think could be improved on, but overall the design and execution of this trike is incredible, it really is a marvel of engineering. This is going to be an amazing back country exploration machine, I cant wait to get out there and have some adventures! 
Stay tuned for an update on my opinions after getting an initial ride in on this trike. Much more to come!

Sunday, September 3, 2017

Unstoppable

Once I put my mind to something, obsession often takes over, and there is no point in even debating with myself because I already know what the outcome is going to be. And so it was, once I discovered fat trikes!

With a long history of bikepacking, and being an early adopter of using fat bikes to get into the back country, it was only a matter of time before I decided that fat trikes would be my post surgery way back into riding off road. I did all the online research and had decided the ICE Full Fat would be my trike of choice. Several people are already using these trikes to get into the back country, most notably the "Trike Hobo" Steve Green. His website Trike Asylum is packed full of information on any trike you could imagine, and he has documented several adventures on his ICE Full Fat. I was lucky enough (very lucky it turns out!) to find one of the ICE Full Fats at my local recumbent shop, Angle Lake Cyclery, and I rushed down there to do a test ride at the first opportunity. And yes, I just have to post another picture of the store...


Standing in the entry of Angle Lake Cycle is an experience you won't soon forget! Back behind those boxes on the left is an ICE Full Fat Trike!


As I said in my last post, Dale is an amazingly nice guy, and despite his store's appearance he has some great products and he isn't bothered by needing to un-bury something to make it available. I asked for a test ride of the Full Fat, and he was more than happy to bring it out. With great excitement I rolled away on the beast, but...

I hated it...I HATED it! 

There was terrible overlap from the front tires and the handlebar/grip area. Every time I turned the wheels the tires raked over my knuckles, and there was no position I could place the bars in where there wasn't either overlap, or severely limited turning radius. This was a full suspension trike and it's handling was muddy, sloppy, and just dumpy feeling. Once I got off the trike to examine it I found slop in the rear suspension pivots allowing the rear wheel to flop back and forth. It felt like ICE just threw some fat bike wheels on one of their other trikes and called it good, like the frame was not actually designed to be a fat trike. It was awful to ride, and there was no way I was going to spend that kind of money on what I felt was such a poor design. I left dejected and crestfallen.

But, as I said, I am nothing if not determined and I knew there had to be a fat trike out there that was better designed for my intended use. Several other brands fell into the cheap, knocked together, Chinese built category, no thanks. Then a video came up on my YouTube feed showing a guy traveling long distance across a (partially) frozen lake on a fat trike, and the trike looked amazing! Here is that video of Jan Zdansky attempting to cross Lake Baikal-



The trike looked to be exactly what I was looking for. Fully rigid, meaning no sloppy pivots or added weight and complication, no hand/tire overlap, the seat was tucked over the rear wheel to increase traction, full fat 26" rims with 5" tire compatibility, a non folding option, standard Tubus rack compatibility, and they were willing to sell me just the frameset so I could build it up myself. It looked to be perfect, so I contacted AZUB and set into motion ordering a frameset all the way from the Czech Republic. After a couple of false starts and stops with bank transfer problems, the money finally went through and the frame was on the way! 

I had built up a custom Carver O'Beast ti fat bike last year shortly before my shoulder fell apart, so I already had almost all the components I needed to build up the trike once it arrived. 



At the annual Winthrop Fat Bike Meetup



Snoqualmie Pass


I will use the XTR shifter and derailleur from the fat bike, the Race Face Next SL cranks, XT cassette, Avid BB7 brakes and levers, the rear wheel, and tires. Then all I need to do is build up the front wheels and start hooking everything up. 



XT cassette, XTR derailleur, and BB7 brake with a Hope Fatsno rear hub, laced to a Sun/Ringle' Mulfut rim, and a Schwalbe Jumbo Jim tire, set up tubeless



Race Face Next SL crank and pedals



Avid levers and XTR shifter


The day finally arrived, and a large box was waiting for me at work. I took it home and unboxed it immediately! AZUB does a fantastic job of prepping the trike to be shipped, and everything arrived safe and sound. 



The shipping box was well packed, double thickness, and arrived undamaged



The saddle has many rows of straps to fine tune the comfort and fit



Micro adjusters and 12 positions allow for an infinite amount of saddle angle adjustment



Red anodized quick release for the seat mount



The boom has a beautiful cable guide



Massive dropouts make for a stiff rear end, despite not having a thru axle



Kingpins are ready for disc brakes



135mm Fat Trike specific quick release front hubs with red accents



AZUB's exclusive sliding seat mount



Massive separable plates with replaceable alignment pins for breaking the frame down for travel



A side pod mount will allow me to use my Ortlieb handlebar bag to keep necessities close at hand



Here is a short video of the trike unboxing


I'm really excited to get this monster built up! Evaluating it after the unboxing shows nice welds, carefully thought out design, and a gorgeous gloss paint job. I am so impressed with the way this trike was engineered, nothing was missed in the well thought out and executed design. From the massive separable frame plates with replaceable alignment inserts, to the internal cable routing through the handlebars, to the 135mm fat specific QR front hubs, to the AZUB exclusive sliding seat mount. This trike is going to be an amazing back country exploration machine! 





















Saturday, September 2, 2017

Continued Evolution

When last we checked in I was "embracing the new normal", and enjoying my new (to me) recumbent bike. Well, as was mentioned then, shoulder problems had sent me down the recumbent path, and my shoulder problems worsened to the point where surgery became inevitable. In February I finally had my right shoulder repaired, and with that came the obvious conclusion that falling off the recumbent after surgery was a really bad idea. And since I was very prone to doing so, I knew in my heart that two wheels was simply too risky for the foreseeable future, or at least until a full and complete recovery had been made. And, seeing as how I was going to have a second surgery on the left shoulder a year later, the chances of riding on two wheels became a fantasy for the future and not part of my current reality. Having gotten through one surgery and the resulting long and painful recovery, there was only one option if I wanted to keep riding. There was gonna be a huge change, the biggest transition for me in cycling yet...it was time for a recumbent trike! 

NOOOOOOOOooooooooooooooo!!!!!!!!!!!!!!

Up to this point, like so many others I thought of trikes as something old people resorted to. But after doing some research I found a vibrant, thriving community of high-performance trike riders, and these trikes are not your grampa's grocery-getter. Some of these trikes cost more than a new car, and they are highly refined and beautifully engineered little speed machines. Test riding several showed me that they are fast, comfortable, but above all, super fun! There is just nothing like the feeling of carving corners on these things while being inches off the ground. It's exhilarating!

Out of the three most popular and extremely high-quality trike manufacturers, I kept coming back to a company called HP Velotechnik as the one most long distance riders toured on. And, as a German company, I had every confidence that their reputation was well deserved. A bit of Craigslist searching found someone local with one of their basic models called a Gekko, and after a test ride and a reasonable (for a trike, they are incredibly expensive compared to bikes!) offer, the nearly new trike was mine! 


Happy, comfortable new triker



Woodland Park



Ready for exploring



Ravenna Park
I'm just realizing that every pic shown here is on dirt!


The Gekko, or "Three Toed Sloth", is a lightweight, folding, fully rigid trike. It is quick, nimble, with a tight turning radius, and a stiff frame. I loved it for all these qualities, but after a couple of months riding it I began to be frustrated by these same qualities. The things that made it perform so well on flat pavement were what made it really beat me up when the road surface became even a little bit rough. No suspension on a recumbent means every imperfection in the pavement gets transmitted straight into your body, and although I tried several small tweaks to improve the comfort, it just wasn't right. Plus, I wanted a trike I could take off-road, and the Gekko was just not going to work for that. I sold the Gekko to a co-worker who was in the market for a trike to commute to work on and started looking for my next trike that would be better suited to a more varied terrain. People like Matt Galat from the JaYoe World Tour, and the guys from Hello Bike World chose Hp Velotechnik to supply them with Scorpion FS20 trikes to take them on their incredible adventures, and they are not the only ones. That was the trike I would look for.

Some phone research led me back to Angle Lake Cyclery, a bike/trike store which has to be seen to be believed! 


The view, standing inside the front door at Angle Lake Cyclery. Yes, it looks like this every day!

The owner Dale Clark is an angel of a man, generous to a fault, and while not exactly a meticulous shop owner, had in stock the exact trike I had my eye on to replace the Gekko, the Scorpion FS20. A deal was made, and I brought home my dream machine. The Scorpion, now known as "Klause", is full suspension, with a high tech MacPherson Strut up front. I don't know how it all works, but I do know the trike is a comfortable, plush, smooth ride, and most bumps in the road are now barely felt. There is a significant weight penalty for all this comfort and technology though, and the Scorpion weighs in at 5 pounds heavier than the comparable svelte (for a trike) Gekko, over 40 lbs with accessories! I say the extra weight is worth it though. The Scorpion is a true Cadilac among trikes. And if Matt Galat and the Hello Bike World guys are riding them, then I know it can handle anything I'm likely to throw at it!


An overnighter on San Juan Island



On the Iron Horse Trail...



...also known as the John Wayne Pioneer Trail



Out for a city ramble


I have been thoroughly enjoying the Scorpion, but I do really miss the true off-road adventures and bike-packing that my fat bike carried me on. And you know what that means...



There's gonna be a new addition to my trike stable soon! 😃







Wednesday, September 21, 2016

Building a Skerry

What I did on my summer vacation

  • Day: Who knows, I lost count
  • Total Build Time: Don't know, don't care. See above

One of the things that has stalled any interest in moving ahead with this boat build is...you guessed it, sanding. You hate, I hate it, we ALL hate it. Using a palm sander to fair the hull was proving to be an exercise in futility, and I knew I needed a random orbital sander to do the job. A good friend offered a loan on a well used Porter Cable unit, and I jumped at the opportunity to save a bunch of money not buying a new sander (although the Festool Rotex is a REALLY nice sander!) I plugged it in, started sanding, and in less than thirty seconds pieces of the sander were flying in every direction! The sanding pad was dry rotted and was disintegrating, throwing pieces of itself everywhere in it's final death throes. Well, now I had a problem. How to sand all that hull without taking forever? Fortunately, I'm a smart guy and knew what the ONLY possible solution was...go out immediately and buy that brand new Festool Rotex!!! What an amazing sander, and it should be for the price! But I'm a firm believer in buying the best and buying once, and Festool is by far the best. It took relatively no time at all to sand the entire hull smooth in preparation for the finish coats of epoxy, which I have yet to apply. 

As a result of continued shoulder issues, the one month sabbatical that I had planned to take in September to do a bike trip had to be postponed until next year, so I decided to take two weeks off anyway and see if the shoulder would recover after being away from work. While slowly getting better it was still not healed, so I decided to just make the best of it. 

September is always my favorite month of the year because of the annual Port Townsend Wooden Boat Festival, which I never miss. This year was particularly beneficial for me because Chesapeake Light Craft had brought their demo Skerry (the same one that inspired me to build mine), and that afforded me the opportunity to have a closer look at it to compare and contrast with my build. Not only was it educational, it also gave me great perspective because they obviously didn't sweat the details anymore than anyone else, and that helped me accept the flaws and problems with mine. No boat is perfect, and as the following pictures show, every build is a balance of good, and "good enough."





The stern fillets on the CLC demo Skerry. Gaps, glops, and god-awful epoxy mess.




Same with the bow. Yeesh.
I'm clearly spending way too much time on trying to make my boat look pretty!




I wanted to have a close look at their bow and stern profiles since this was what I had to do next. Even their bow is a bit asymmetrical. The varnish looks nice though!




Same with their stern. These both show something important that will come up later.


Now, back to MY boat build!  


I had to do some cleanup on my rails in preparation for rounding them over. I found that my Lie Nielsen large rabbit plane fit the rails PERFECTLY. This made short work of cleaning up the undersides of the rails, and keeping them square.






Once I had the rails cleaned up I started to work on roughing out the radius for the bow...




...and stern.

This brought out a big challenge. CLC tells you to round over the bow and stern of the upper panels...BEFORE putting on the rails. WTF? Why would you do that? Now you have a round profile that you have to bring two square rails in to meet! Grrrr. As you can see if you look closely, the rails have a gap at the rounded part of the bow and stern. And, looking back at their finished boat you can see that they just continued sanding back until the rails met the panels. If the panels were left sharp until this point you would have a finer entry and exit point at the rails. Dammit! Well, get out the block plane, surefire rasp, and sanding block and get to work!


Stern roughed out...



...and the bow.

The next step was to round over the rails. I wouldn't know what the final bow and stern profile was going to be until I figured out the rounded over shape, so I grabbed my router and a 3/8" roundover bit and...the bit didn't fit through the router base plate. Crap. I was going to have to free-hand the round-overs with the router, top and bottom! Yikes! 
It made sense to be concerned about this step because I screwed up, BIG TIME. The rails taper at each end and this made the router dig in really bad on the bottom of the rail. So bad in fact that I thought I was going to have to cut a bunch of material away and put in a patch. Funny enough though, as I started to remove material to taper and hand round-over the rails...I ended up having to take so much off to bring the rails back past the gaps that I had enough rail to work with when all was said and done! HUGE sigh of relief!!!



Beginning the shaping after the round-over disaster. Yep, I sanded through the veneer of the breast hook. It looks way worse here than in real life, and I really don't give a damn at this point! 




Less of an issue in the stern, this looks really nice




Beautiful round-over with a nice scarf!




 I also needed to put a fillet along the skeg. This was one of the only things I have done on this boat that went smoothly!




I put the boat on my little ultralight Yakima trailer to move it around for sanding, epoxy, etc.




The final pic for this post. After sanding the exterior it's truly looking at its ugliest! Pretty soon it will start to look much nicer as the epoxy, paint, and varnish go on. At least I hope it does.

I was also very excited that during the final "sail-by" at the Wooden Boat Festival one of the guys from CLC had their Skerry out on the water and I was able to see first hand how it sails. I have to say, I was very impressed! The boat was really stiff and heeled very little. It's also fast! I watched it run away from CLC's PocketShip, a much bigger boat that carried a lot more sail area. The Skerry is also a very pretty boat under sail, which is important! Seeing it helped get me inspired again to get back to work on mine, and seeing the quality of their build helped me get mine back in perspective. Below you will see a quick video of the CLC boat coming into the beach at the end of the sail-by. Until next time, enjoy!